Summer has passed, the temperature began to cool after the fall, the climate changed significantly. The transition from summer to autumn, the forklift in the use of the process should pay special attention to maintenance. gzsycc.com suggest you, this season forklift maintenance should do the following: 1.A vehicle external forklift maintenance Autumn morning and evening dew more water, forklift surface is often very wet, if the body has obvious scratches, should be done in time to do paint treatment, so as not to scratches the site of moisture and corrosion. Due to the corrosion of rain acid and summer light point-blank, the forklift body paint will inevitably be oxidized, at the time of the season, you'd better do for the forklift from the surface cleaning, paint maintenance work. 2.Forklift Tire maintenance In the safe driving of the forklift, the tires play an important role. In the summer, due to the high temperature, forklift user always check the tire pressure, must not make the tire pressure is too high, otherwise, there will be the risk of forklift tire puncture. But to the fall, because the temperature is relatively low, the tire will add air pressure to make it Keep the specified pressure range, at the same time, should also check whether the tire scratches, because the rubber in the autumn and winter is easy to harden and more brittle, easy to leak the tires, and even tires, to regularly clean the inclusions within the tire. 3. Forklift maintenance of  the engine compartment Should check the engine compartment of the engine oil, brake oil and antifreeze, to see if the oil is sufficient, whether the deterioration, whether to replace the cycle, the oil is like the vehicle's blood, to the replacement cycle must be replaced to ensure that the oil cycle unobstructed. 4. Forklift maintenance of  barake system Autumn day and night temperature difference, easy to cause the forklift body parts expansion shrinkage deformation, you should always check whether the brake weak, deviation, brake pedal pedaling force has changed, if necessary, clean up the entire brake system piping part and pay attention to forklift maintenance. If your forklift is equipped with a warm air line or fan, after a summer operation, or for the upcoming cold winter to prepare, the fall of the most suitable for these devices to check whether the exhaust outlet is normal, the line is aging, etc. And so on, if any problem can be resolved in time. 5. Maintenance of air inlet or inlet grille To check whether these parts are debris, if there are debris, you can use compressed air blowing dust, in addition, forklift maintenance to the engine cooling state, you can use a water gun from the inside to wash the above parts. 6. Air conditioning maintenance If your forklift is equipped with air conditioning, hot summer weather, the car is often overloaded air conditioning operation, in addition, due to summer and autumn more rain, a long time, it is easy to rust the condenser...

Forklift radiator is use water or cooling liquid ，to reduce the  heat when the engine is running .if there is a long time not to check or repair the radiator.it will effect the efficiency of the engine or cause the breakdown of the engine parts . So this page is going to explain how to check and repair the radiator when maintain the forklift in the routine. 1、Forklift radiator check （1）check the tear：put the radiator into the water channel，filling the compressed air into the hole of the radiator（plug up by other hole），pressure is 0，1 MPa，if the radiator . If come for bubble from radiator ，it means the radiator corrode ，if the bubble come little ，it means it isn't serious，if finds break ，make a mark，in order to repair. （2）Check the rediator silt up ，according to the water crushed into radiator，it can analyze if the radiator slit up or block. 2、Forklift radiator repair （1）Clean up incrustation of the radiator，when the water capacity decrease ，or there is incrustation in the radiator，the soda lye (mass  fraction  is 10%) should be  get heated to 90 ℃ to fill  up the radiator and put it with 1-2 hours and then wash it with hot water .（ps： caustic soda is  sodium hydroxide ，it also call NAOH, is a corrosive  with strong corrosive ）. （2）When the radiator is block up ,use the Exclusive core   to clear away. （3）When the radiator core is serious deformation,curve or the pipe exsit hole can be sealed (can’t be above 10%of the whole). （4）The deformation cooling fin can be straightened. （5）The repair of the tear of the radiator .the tear of the raidator can be repaired with Tin soldering,before welding,rub the tear to show up metallic luster,and coat ta layer of  Zinc chloride flux in the connection ,repair the connection with Tin soldering when heating. Forklift radiator repair is establish in the radiator still can be repaired ,if the radiator is overaging or have a serious broken ,we suggest to replace a new one ,please feel  free to contact our saleman to choose the right product for u ,thanks!